Ready Service Solutions logo

Tile Installation in Sioux Falls, SD

Ready Service Solutions installs tile for floors, showers, backsplashes, and bathroom walls throughout Sioux Falls and the surrounding Tea, SD area — with full project oversight from start to finish.

Licensed, bonded, and insured, we handle everything from layout and substrate prep to grouting and sealing so your tile work holds up for years.

Tile Work We Install

Whether you are updating a bathroom floor, building a custom tile shower, or adding a kitchen backsplash, we approach every installation the same way: proper substrate, correct thinset, tight joints, and finished grout that stays clean.

We work with ceramic, porcelain, and natural stone tiles in a wide range of formats — from small mosaic sheets to large-format slabs. Each material has different handling requirements, and we account for those differences in every layout and installation decision.

Tile work is closely connected to our bathroom remodeling and flooring services, so if your project involves more than just tile — new plumbing fixtures, a vanity, or new subfloor — we can scope and manage the full job under one project.

  • Shower walls and floors
  • Bathroom floor tile
  • Kitchen backsplash tile
  • Laundry room and utility floor tile
  • Entryway and mudroom tile
  • Basement floor tile

What Goes Into a Proper Tile Installation

The tile itself is only part of the job. What sits behind and beneath the tile determines whether it lasts five years or twenty-five.

For wet areas like showers, waterproofing the substrate is non-negotiable. That means installing cement board or an equivalent backer, applying a waterproof membrane at seams and transitions, and sloping the floor correctly toward the drain. Skipping or shortcutting any of these steps leads to water intrusion behind the tile, mold, and eventual tile failure — problems that cost far more to fix than to prevent.

For floor tile, the subfloor must be flat, solid, and deflection-free before any tile goes down. We assess the existing structure before we start and address any flex or unevenness, because tile and grout crack when the floor moves under them.

  • Substrate evaluation and repair before tile begins
  • Waterproof membrane installation in all wet areas
  • Correct thinset selection for the tile type and substrate
  • Layout planning to minimize small cuts at focal points
  • Grouting with appropriate joint width and grout type
  • Sealing porous tile and grout where needed

Serving Sioux Falls and the Tea, SD Area

Ready Service Solutions is based in the Sioux Falls area and regularly works in Tea, SD and throughout Minnehaha and Lincoln counties. Sioux Falls sits on the prairie with significant temperature swings between seasons — winters regularly push well below zero and summers climb into the nineties. That thermal range matters for tile: floors installed over concrete slabs on grade or in basements can experience movement as the slab responds to ground temperature changes, which is one reason we pay close attention to expansion joint placement and flexible grout at transitions.

Sioux Falls follows South Dakota state building code requirements, and bathroom and wet-area tile work in permitted remodels must meet those standards. We build to code on every job and can coordinate with the city inspection process when a permit is required for the broader project.

Homes across Sioux Falls neighborhoods — from established areas near downtown to newer construction in the growing southwest corridor — present different flooring and substrate conditions. Older homes may have original subfloor layers that need reinforcement before large-format tile can go down. We evaluate the specific conditions at your home before committing to a scope.

How the Process Works

We start with a walkthrough of the space so we can see the substrate, measure the area, and understand what you are trying to accomplish. From there we provide a written estimate that covers demo if needed, any substrate work, the installation itself, grouting, and cleanup.

We do not hand the job off after the estimate. The same team that scopes the work sees it through to completion, and we keep you informed at each stage so there are no surprises on timeline or scope.

If your tile project is part of a larger bathroom remodel or flooring replacement, we can sequence the work so tile, fixtures, and finish materials go in at the right time — no rework, no waiting on separate contractors to coordinate.

Common Questions

How do I know if my existing floor or wall can handle tile without extra prep work?

We check for deflection, levelness, and moisture before anything else. A floor that flexes or a wall with soft drywall behind it will cause tile and grout to crack no matter how good the installation is. If we find issues during the walkthrough, we tell you what needs to happen before tile can go down and include that scope in the estimate — nothing gets started until the substrate is ready.

Can you remove old tile and install new tile, or do you only do new installations?

We handle full tile replacement jobs, which means demo of the existing tile, assessment of what is underneath, any needed substrate repairs, and then the new installation. Removing tile sometimes reveals water damage, failed backer board, or subfloor issues that need to be addressed before new tile goes in, so we account for that possibility in how we scope replacement projects.

Do I need a permit for tile installation in Sioux Falls?

Tile installation by itself typically does not require a separate permit in Sioux Falls, but if the tile work is part of a bathroom remodel that includes plumbing or structural changes, the broader project may require permits and inspections. We can walk you through what applies to your specific job during the estimate and handle permit coordination when it is needed as part of a larger remodel.

Get a Free Tile Installation Estimate

Reach out to schedule a walkthrough of your project and receive a written estimate with no obligation.